Broan EW5836SS Installation Guide download pdf (Page 7)

MODELS EW5830SS • EW5836SS

Page 7

Always turn the hood ON before cooking in order to establish an air

flow in the kitchen. After turning off the range, let the hood run for a

few minutes to clear the air.

Operate the hood as follows:

OFF

Turns the fan OFF

FAN (1-Pushbutton Switch, 3-Fan Speeds)

Turns the fan ON to the last selected speed, and activates a blue LED

indicating the fan speed setting. Pressing the FAN button a second

time will index the fan speed and LED indicator to the next highest

setting. Pressing the FAN button when the fan is at the highest speed

setting will index the fan and LED indicator to the lowest setting.

DELAY-OFF (10 Minute Delay-OFF)

Activates the 10 minute delay off feature when the fan is ON (any

speed). When activated, the blue LED indicator above the selected

speed setting will blink. The hood fan will automatically turn OFF after

10 minutes has elapsed. The DELAY-OFF button can be pressed at

any time during the 10 minute countdown to turn off the feature.

LIGHT (1-Pushbutton Switch, 3-Light Intensities)

Turns the lights ON to the lowest intensity. Pressing the LIGHT button

a second time will index the light intensity to the next highest level.

Pressing the LIGHT button when the lights are at the highest intensity

will turn the lights off.

FILTER CHANGE INDICATION

After 30 hours of fan operation, the three blue LED indicators will blink

simultaneously, indicating that it is time to clean the grease filters.

To reset the filter clean timer, press and hold the OFF button for 3

seconds. The blinking LED indicators will turn off.

HEAT SENTRY SYSTEM

This range hood is equipped with a standard Heat Sentry system

that monitors excessive temperature and automatically turns the fan

speed on HIGH.

1) If the fan is ON, the Heat Sentry system will increase the fan

setting to its highest speed when the temperature is elevated.

The blue indicator for fan speed (3) will illuminate and blink at

a high rate, indicating that the heat sentry function is activated.

Once the temperature has reduced, the Heat Sentry system will

change the fan speed to the original setting.

2) If the fan is OFF, the Heat Sentry system will automatically turn

the fan on to its highest speed when the temperature is above

normal. The blue indicator for fan speed (3) will illuminate and

blink at a high rate, indicating that the heat sentry function is

activated. After the temperature has lowered to normal, the fan

will turn off.

OPERATION

FUSES

The Range Hood Control Board contains a Main Fuse to protect the

controls from power surges. New fuses can be purchased at a local

electronic supply store. Use 5A, 120V, 5 mm diameter, 20 mm long,

fast-acting, cartridge-type fuses.

To replace a fuse (by qualified person(s):

1. Disconnect power at service entrance.

2. Remove filters

3. Remove control cover

4. Remove and inspect fuse.

MAKE-UP AIR DAMPER

The hood is compatible with Broan Make-Up Air Damper Model

MD6T or Model MD8T (optional). Purchase separately.

Make the connection to the Make-Up Air Damper with low voltage

wiring, as shown. See Make-Up Air Damper instructions for additional

information.

REMOTE CONTROL

The hood is compatible with Broan Radio Frequency (RF) Remote

Control Model BCR1 (optional). Purchase separately.

To link the BCR1 remote control with the hood, press and hold the

LIGH T button for 3-seconds.

The blue LED indicators will turn on and off in succession to indicate

the hood is in RF linking mode. When in the linking mode, press any

key on the RF remote. An audible beep will be heard at the hood, and

the hood LED’s will stop blinking if a successful link is accomplished.

If the remote control did not successfully link with the hood, the linking

mode will be deactivated after 12 seconds, and the LED’s will stop

the sequential blinking. Refer to the BCR1 instructions for additional

information.

OFF FAN

DELAY

OFF

LIGHT

FAN SPEED

LED INDICATORS

MAKE-UP AIR DAMPER

HOOD

24V

TRANSFORMER

(INCLUDED)

GRD

DRY CONTA

TERMINAL

BUSHING

FOR LOW

VOLTAGE

CONNECTION

MAKE UP DAMPER CONNECTION

(switched low voltage)

20 GAUGE BELL WIRE FOR LOW

VOLTAGE CONNECTION ON

TOP OF HOOD

120 VAC

60 HZ

1 2 3 4 5 6 7 8 9 10 11 12 ... 27 28

Comments to this Manuals

No comments

Broan EW5836SS Installation Guide Page 7

Comments to this Manuals

Related products and manuals for Cooker hoods Broan EW5836SS