Broan QP130SS Operations Instructions download pdf (Page 2)

MODELS QP130BL • QP130BLC • QP130SS • QP130SSC

QP130WW • QP130WWC • QP136BL • QP136SS • QP136WW

Page 2

OPERATION

Always turn the hood ON before cooking in order to establish an

air flow in the kitchen. After turning off the range, let the hood run

for a few minutes to clear the air.

Operate the hood as follows:

1 20

BLOWER SWITCH

This 3-position rocker switch turns blower ON and OFF and

controls blower speed.

Left rocker position (0) turns blower OFF.

Center rocker position (1) turns blower ON to low speed.

Right rocker position (2) turns blower ON to high speed.

LIGHT SWITCH

This 3-position rocker switch turns lights ON and OFF and controls

their intensity.

Left rocker position (0) turns lights OFF.

Center rocker position (1) turns lights ON to low intensity.

Right rocker position (2) turns lights ON to high intensity.

NOTE:

This hood utilizes an offset blower design to achieve greater

performance and lower sound levels. As a result, you may notice

that cooking impurities are more attracted to one side or appear

to be pulled-in faster than they appear on the opposite side. This

is completely normal. The hood has been designed and tested to

provide good capture of cooking impurities and odors under all

normal cooking conditions regardless of the cooking location on the

cooktop. Please note that cooking on the rear burners will always

result in the best capture results, regardless of the hood design.

CLEANING & MAINTENANCE

For performance, appearance, and health reasons, clean filter,

fan and grease-laden surfaces. Use only a clean cloth and mild

detergent solution on stainless and painted surfaces.

Clean all-metal filters in the dishwasher using a non-phosphate

detergent. Discoloration of the filter may occur if using phosphate

detergents, or as a result of local water conditions - but this will

not affect filter performance. This discoloration is not covered by

the warranty.

Clean the non-duct recirculating filter surfaces frequently with

a damp cloth and a mild detergent. DO NOT immerse filters in

water or put in dishwasher. The special “Clean Sense” feature

indicates when the filter is to be replaced. The blue and yellow

strips will blend to green when it is time to change the filter. The

“Clean Sense” feature works best when facing toward the cook-

ing surface. Change the non-duct recirculating filters every 6

months. For replacement non-duct recirculating filters - purchase

S99010353 or Model BPPF30 for 30” hoods, or S99010354 or

Model BPPF36 for 36” hoods.

The motor is permanently lubricated and never needs oiling. If

the motor bearings make excessive or unusual noise, replace

the motor with the exact service motor. The impeller should also

be replaced.

Use 120

V, 35

W, shielded halogen bulbs - MR16 with GU10 base.

Purchase bulbs separately.

CONTENTS

(2)

GREASE

FILTERS

(1) 3¼” X 10”

DAMPER / DUCT

CONNECTOR

(1) 7” ROUND

DUCT

CONNECTOR

(1)

BULB

SUCTION

CUP TOOL

(1) PARTS BAG CONTAINING:

(3)

WIRE

NUTS

INCLUDED WITH THE HOOD:

(9)

#8 X 1/4”

DUCT

CONNECTOR

SCREWS

(5)

#10 X 5/8”

RD. HD.

MOUNTING

SCREWS

PREPARE HOOD LOCATION

SOFFIT

24" - 30" ABOVE

COOKING SURFACE

CABINET

3¼" X 10" DUCT

(For horizontal discharge)

WALL CAP

ROOF CAP

3¼" X 10" or

7" ROUND DUCT

(For vertical

discharge)

HOUSE WIRING

(Top or Back of hood)

HOODHOOD

1 Determine whether hood will discharge vertically (3¼”

x 10” or 7” Round), or horizontally (3¼” x 10” only). For

vertical or horizontal discharge, run ductwork between

the hood location and a roof cap or wall cap. For best

results, use a minimum number of transitons and elbows.

1 2 3 4 5 6 7 ... 19 20

Comments to this Manuals

No comments

Broan QP130SS Operations Instructions Page 2

Comments to this Manuals

Related products and manuals for Cooker hoods Broan QP130SS