Broan 332H User Manual download pdf

Page Lm

MODEL

331H

or 332H

EXTERIOR

BLOWER

WALL HOOD

CANOPY

(island canopy

available)

10" ROUND DUCT

SOFFIT

ROUGH-IN

PLATE

24" or 27"

18"

10" ROUND ELBOW

DUCT

OPENING

COVER PLATE

MODEL

331H

or 332H

EXTERIOR

BLOWER

WALL HOOD

CANOPY

(island canopy

available)

10" ROUND DUCT

SOFFIT

ROUGH-IN

PLATE

24" or 27"

18"

DUCT

OPENING

COVER

PLATE

MODEL 331H or 332H

EXTERIOR BLOWER

WALL HOOD

CANOPY

(island canopy

available)

10" ROUND

DUCT

SOFFIT

24" or 27"

18"

ROUGH-IN

PLATE

DUCT

OPENING

COVER PLATE

READ AND SAVE THESE INSTRUCTIONS

FOR USE WITH RANGEMASTER HOODS AND ECLIPSE DOWNDRAFT VENTILATORS

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR

INJURY TO PERSONS, OBSERVE THE FOLLOWING:

1. Use this unit only in the manner intended by the manufac-

turer. If you have questions, contact the manufacturer at the

address or telephone number listed in the warranty.

2. Before servicing or cleaning unit, switch power off at service

panel and lock the service disconnecting means to prevent

power from being switched on accidentally. When the service

disconnecting means cannot be locked, securely fasten a

prominent warning device, such as a tag, to the service panel.

3. Installation work and electrical wiring must be done by a

qualified person(s) in accordance with all applicable codes

and standards, including fire-rated construction codes and

standards.

4. Sufficient air is needed for proper combustion and exhaust-

ing of gases through the flue (chimney) of fuel burning

equipment to prevent backdrafting. Follow the heating equip-

ment manufacturer's guideline and safety standards such as

those published by the National Fire Protection Association

(NFPA), and the American Society for Heating, Refrigeration

and Air Conditioning Engineers (ASHRAE), and the local

code authorities.

5. When cutting or drilling into wall, or ceiling, do not damage

electrical wiring or other hidden utilities.

6. Ducted fans must always be vented to the outdoors.

7. To reduce risk of fire, use only metal ductwork.

8. This unit must be grounded.

CAUTION

1. For general ventilating use only. Do not use to exhaust

hazardous or explosive material and vapors.

2. To avoid motor bearing damage and noisy and/or unbalanced

impellers, keep drywall spray, construction dust, etc. off power

unit.

3. Please read specification label on product for further informa-

tion and requirements.

4. Electrical circuit, including speed control, (if used), must be

rated 6 AMPS minimum for Model 332H or 3 AMPS minimum

for Model 331H.

1. Locate the blower so the length of the duct run and number of

elbows and transitions needed are kept to a minimum.

Please note - when using blower with the Broan Eclipse

Downdraft: The downdraft has a 3¼" x 10" discharge.

Transitions are available to connect it to the 10" round

inlet on this exterior-mounted blower.

ALL INSTALLATIONS

MODEL VOLTS AMPS CFM DUCT SIZE

331H 120 2.4 600 10 " DIA.

332H 120 5.7 900 10" DIA.

INSTALLER: Leave This Manual With The Homeowner

HOMEOWNER: Use And Care Information On Page 3

MODELS 331H & 332H

EXTERIOR MOUNTED BLOWER

SPECIFICATIONS

PLAN THE INSTALLATION

TYPICAL ROOF MOUNTED INSTALLATION

(Vertical discharge)

TYPICAL WALL MOUNTED INSTALLATION

(Vertical discharge - elbow to horizontal)

TYPICAL WALL MOUNTED INSTALLATION

(Horizontal discharge)

2. Where possible, blower should be centered between wall

studs or roof rafters.

3. Avoid pipes, wires, or other ductwork that may be running

through the wall.

4. Be sure that there is enough space for any transitions that may

be needed between the blower and the connecting ductwork.

5. For best performance, locate transitions nearest to ventilator

(i.e. downdraft).

NOTE: Horizontal discharge requires relocation of the duct open-

ing cover plate. See hood manual for instructions.

1 2 3 4 5 6 ... 11 12

Summary of Contents

Page 1 - EXTERIOR MOUNTED BLOWER

Page Lm1MODEL331Hor 332HEXTERIORBLOWERWALL HOODCANOPY(island canopyavailable)10" ROUND DUCTSOFFITROUGH-INPLATE24" or 27"18"10"

Page 2

10PREPARE EL LUGAR DE LAINSTALACIÓNINSTALACIONES EN EL TECHOPREPARE EL LUGAR DE LAINSTALACIÓNINSTALACIONES EN LA PAREDTODAS LAS INSTALACIONES1. Ubique

Page 3 - INSTALL THE BLOWER

Page Lm111. Quite los clavos del techo de las 2/3 partes de las tejassuperiores que se encuentran alrededor del área de corte ylevante las tejas con c

Page 4 - SERVICE PARTS

12CLAVEN.º PIEZA Nº. DESCRIPCIÓN1 97011795 Conjunto de la caja de ventilación2 98008507 Regulador de tiro3 93260454 Tuerca para metales, #18-18 tipo U

Page 5

211" dia.hole29½"11" dia.hole1¼"dia. hole127/8"10¾"25"7¼"7¼"1¼"dia. hole91/8"91/8"Wall Stu

Page 6

1. Remove roofing nails from the upper 2/3 of theshingles around the cutout area and carefully lift theshingles to allow the back flashing sheet on th

Page 7 - INSTALLATION DU VENTILATEUR

4KEYNO. PART NO. DESCRIPTION1 97011795 Airbox Assembly2 98008507 Damper3 93260454 Sheet Metal Nut, #18-18 U-Type (7 req.)*4 99100484 Isolator (3 req.)

Page 8 - PIÈCES DE RECHANGE

Page Lm5MODEL331Hor 332HEXTERIORBLOWERWALL HOODCANOPY(island canopyavailable)10" ROUND DUCTSOFFITROUGH-INPLATE24" or 27"18"10"

Page 9 - MODELOS 331H Y 332H

61. Choisissez une position sur le mur extérieur. Assurez qu'il n'ya pas de colombage, tuyaux ou fils dans l'endroit qui seraouvert.PRÉ

Page 10 - 24¾"

Page Lm71. Retirez les premiers deux tiers des clous à toiture desbardeaux se trouvant autour de la surface de découpe puissoulevez délicatement les b

Page 11 - INSTALE EL VENTILADOR

8REPÈRE N° PIÈCE DESCRIPTION1 97011795 Boîte à air2 98008507 Clapet3 93260454 Écrou à tôle, n° 18-18 Type U (7)*4 99100484 Isolateur (3)5 99260477 Écr

Page 12 - PIEZAS DE REPUESTO

Page Lm9MODEL331Hor 332HEXTERIORBLOWERWALL HOODCANOPY(island canopyavailable)10" ROUND DUCTSOFFITROUGH-INPLATE24" or 27"18"10"