Broan 512M Installation Guide download pdf

INSTALL THE VENTILATOR

WARNING: WHEN CUTTING OR DRILLING INTO WALL,

DO NOT CUT EXISTING ELECTRICAL WIRING.

CAUTION: Do not mount the ventilator above a cook-

ing surface.

CAUTION: Measure and mark the center of wall open-

ing on inside and outside walls before cutting open-

ing.

1. Cut a 6" diameter opening in the wall.

PLAN THE INSTALLATION

The ventilator can be installed in outside walls walls up to 10" thick.

Walls less than 6" thick will not use the adjustable duct. Choose a

location with no obstructions, such as wall studs, plumbing or electrical

wiring.

The ventilator can be controlled using a wall switch or speed control

(available separately).

CAUTION

1. For general ventilating use only. Do not use to exhaust hazardous

or explosive materials and vapors.

2. To avoid motor bearing damage and noisy and/or unbalanced

impellers, keep drywall spray, construction dust, etc. off power unit.

3. Please read specification label on product for further information

and requirements.

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY

TO PERSONS, OBSERVE THE FOLLOWING:

1 . Use this unit only in the manner intended by the manufacturer. If you

have questions, contact the manufacturer at the address or tele-

phone number listed below the warranty.

2. Before servicing or cleaning unit, switch power off at service panel

and lock the service disconnecting means to prevent power from

being switched on accidentally. When the service disconnecting

means cannot be locked, securely fasten a prominent warning

device, such as a tag, to the service panel.

3. Installation work and electrical wiring must be done by qualified

person(s) in accordance with all applicable codes and standards,

including fire-rated construction codes and standards.

4. Sufficient air is needed for proper combustion and exhausting of

gases through the flue (chimney) of fueling equipment to prevent

backdrafting. Follow the heating equipment manufacturer’s guide-

line and safety standards such as those published by the National

Fire Protection Association (NFPA), and the American Society for

Heating, Refrigeration and Air Conditioning Engineers (ASHRAE),

and the local code authorities.

5. When cutting or drilling into wall or ceiling, do not damage electrical

wiring and other hidden utilities.

6. Ducted fans must always be vented to the outdoors.

7. To reduce the risk of fire, use only metal ductwork.

8. This unit must be grounded.

READ AND SAVE THESE INSTRUCTIONS

MODELS 512M, 512MMX

THROUGH-THE-WALL VENTILATOR

2. Unplug motor, loosen screw and remove electrical wiring box

cover.

3. Push electrical wiring box into housing and lift out.

Note: For easier removal of wiring box, remove the motor assembly.

Loosen the mounting screws and rotate the motor assembly

clockwise.

VENTILATOR

GRILLE

WALL

CAP

ADJUSTABLE

DUCT

5¼" TO 10"

1 2 3 4

Summary of Contents

Page 1 - THROUGH-THE-WALL VENTILATOR

INSTALL THE VENTILATORWARNING: WHEN CUTTING OR DRILLING INTO WALL,DO NOT CUT EXISTING ELECTRICAL WIRING.CAUTION: Do not mount the ventilator above a c

Page 2

WIRE THE VENTILATORWARNING:SWITCH POWER OFF AT SERVICE PANEL AND LOCK SERVICEPANEL BEFORE MAKING ELECTRICAL CONNECTIONS.WHITEBLACK120/127 VACPOWER CAB

Page 3 - VENTILADOR EMPOTRADO

PREPARACION DE LAINSTALACIONEl ventilador puede instalarse en paredes exteriores hasta 25,4 cm deespesor. No se usa el ducto ajustable en paredes de

Page 4 - PIEZAS DE SERVICIO

ADVERTENCIA: DESCONECTE LA CORRIENTE EN EL PANEL DESERVICIO Y BLOQUEE EL PANEL DE SERVICIO ANTES DE HACERLAS CONEXIONES ELECTRICAS.1. Sujete el cable