Broan BCR1 Installation Guide download pdf

MODEL BCR1

Page 1

RANGE HOOD

REMOTE CONTROL

READ AND SAVE THESE

INSTRUCTIONS

Your Broan BCR1 remote control is a Radio

Frequency (RF) wireless device used to operate

the fan, lights, and delay-off feature on compatible

Broan range hoods. Refer to your hood installation

manual or product specification sheet to ensure

your hood is compatible with Broan model BCR1

remote control.

Unlike Infrared (IR) remotes, which are the most

common, RF remotes are easier to use because

they do not require line of sight, so they do not

have to be aimed directly at the equipment they

are controlling. RF is a very convenient, reliable

method to transmit commands without wires for

the operation of your compatible range hood.

This system will offer exceptional performance

in most cases. Although signals will often travel

great distances, as well as around and through

structures/walls, there are some limitations to the

operating range. See troubleshooting guide on

page1 regarding these limitations.

CONTROL OPERATION

When a button is depressed on the remote control,

it sends a coded signal to the receiver installed

on a Broan compatible hood, telling it which

function to activate.

Light Button – When the hood lights are OFF,

pressing the light button will turn the hood lights

ON to the lowest setting. Pressing again will index

the lights to the next highest setting. When lights

are at the highest setting, pressing the button again

will turn lights OFF.

Fan Button – When the hood fan is OFF,

pressing the fan button will turn the hood fan ON

to the lowest setting. Pressing again will index the

fan speed to the next highest setting. When hood

fan is at its highest setting, pressing the button

again will turn fan OFF.

Delay off Button – When hood fan is ON,

pressing the Delay-OFF button will activate the

Delay-OFF feature of the hood. Pressing again will

turn the DELAY-OFF feature OFF. If the hood fan is

OFF, pressing the button will have no effect.

The green LED indicator on the remote will

illuminate to indicate that the function has been

transmitted. An audible “beep” at the hood, and

change in function will indicate that the hood has

received the transmission.

Your Broan remote control comes equipped

with magnetic, non-slip feet. It can be adhered

to a vertical metal/magnetic surface (such as a

refrigerator door) or placed on a horizontal surface.

LED INDICATOR

FANDELAY-OFFLIGHT

The RF encoder on your remote control is a fixed

address encoder, meaning the address (security)

code can be changed to another code manually.

There exists a slight possibility of interference from

other RF remote controls (garage door transmitter,

home and car security systems, remote control

paddle fans, other range hoods installed nearby).

To resolve interference issues, the address or

code can be changed (up to 32 independent

address codes) by changing the settings on the

5 position DIP switches on the handheld remote

and compatible range hood. Note that in most

cases, this will not be necessary. The product is

shipped from the factory (transmitter and receiver)

with DIP address settings set to matching codes

(switch 1 set to ON - switches 2-5 set to OFF). Assuming

there are no interference issues, the user won’t need to

change the DIP switch address code settings.

CHANGING SECURITY CODES

Remote (Transmitter)

Open the back cover of the remote by removing

the center screw, and placing a flat screwdriver in

between two halves of the housing to pry apart.

Locate the 5-position DIP switch on the circuit board.

Using a small insulated screwdriver or other non-

conductive instrument, adjust one or more of the

5 DIP switches to a different position (ON or OFF).

Note that SWITCH “1” was factory-set to the “ON”

position and SWITCHES “2-5” were factory-set

to the “OFF” position. Prior to re-assembling the

remote, carefully note the new DIP switch settings

so the same settings can be used on the hood

(receiver). Carefully reassemble the remote.

Hood (Receiver)

WARNING – TO REDUCE THE RISK OF FIRE,

ELECTRIC SHOCK, OR INJURY TO PERSONS,

OBSERVE THE FOLLOWING: IF YOU HAVE

QUESTIONS, CONTACT THE MANUFACTURER AT

THE ADDRESS OR TELEPHONE NUMBER LISTED

IN THE WARRANTY. BEFORE SERVICING OR

CLEANING UNIT, SWITCH POWER OFF AT SERVICE

PANEL AND LOCK THE SERVICE DISCONNECTING

MEANS TO PREVENT POWER FROM BEING

SWITCHED ON ACCIDENTALLY.WHEN THE

SERVICE DISCONNECTING MEANS CANNOT BE

LOCKED, SECURELY FASTEN A PROMINENT

WARNING DEVICE, SUCH AS A TAG, TO THE

SERVICE PANEL. ELECTRICAL WORK MUST

BE DONE BY A QUALIFIED PERSON(S) IN

ACCORDANCE WITH ALL APPLICABLE CODES

AND STANDARDS.

Locate the 5-position DIP switch on the hood

(usually located on the circuit board) – refer to your

hood installation instruction for additional details

if necessary.

Using a small insulated screwdriver or other non-

conductive instrument, adjust the DIP switches

to the same settings as the remote control.

Reassemble any parts from hood that were removed

to access the DIP switches.

1 2 3 4 5

SWITCH “1”

SHOWN “ON”

SWITCHES “2-5”

SHOWN “OFF”

Verify the function of the remote control and hood

once DIP switch settings are properly paired. New

settings may be needed if interference issues are

still encountered.

CLEANING AND MAINTENANCE

Clean surfaces with a damp, clean cloth and mild

detergent only.

Do not immerse in water. Your remote is

considered to be “splash-proof”, not “waterproof”.

Your Broan remote transmitter is a user friendly

device designed for years of trouble free operation.

Under most circumstances it should require only

periodic battery replacement. The transmitter

is powered by a long life A23-style 12V battery

available at most hardware stores or home centers.

The battery on your remote control should last in

excess of 1-year under normal operation.

To change the battery, remove the battery cover

by using a small flat bladed screwdriver to gently

pry open. Remove existing battery utilizing a

small insulated flat bladed screwdriver or other

non-conductive instrument, and discard properly

with consideration to local codes and recycling

guidelines. Install the new battery while ensuring

the “+” side of the battery lines up with the “+”

terminal of the remote. Replace cover.

WARNING

–

TO PREVENT POSSIBLE SERIOUS

INJURY OR DEATH: NEVER ALLOW SMALL

CHILDREN NEAR BATTERIES. IF BATTERY IS

SWALLOWED, IMMEDIATELY NOTIFY DOCTOR

Notice: Operation is subject to the following

two conditions: (1) This device may not cause

interference, and (2) this device must accept any

interference that may cause undesired operation of

the device.

TROUBLE SHOOTING GUIDE

Remote transmitting signal (green LED

illuminates) but hood not receiving

• Ensure hood is powered.

• Battery weak – install new fresh A23-12V battery

• Check the receiver and transmitter dip switches

are set at the same setting.

Transmission Range Short

• Change orientation of remote when activating

• Change location of remote to minimize

obstructions

• Battery weak – install new fresh A23-12V battery

Interference encountered with other RF

transmitters or receivers

• Change encoder DIP switch settings

1 2 3 4 5

SWITCH “1”

SHOWN “ON”

SWITCHES “2-5”

SHOWN “OFF”

1 2 3 4

Summary of Contents

Page 1 - REMOTE CONTROL

MODEL BCR1Page 1RANGE HOODREMOTE CONTROLREAD AND SAVE THESEINSTRUCTIONSYour Broan BCR1 remote control is a Radio Frequency (RF) wireless dev

Page 2 - DEHOTTE DE CUISINE

MODÈLE BCR1Page 2TÉLÉCOMMANDE DEHOTTE DE CUISINELIRE CES DIRECTIVES ETLES CONSERVERVotre télécommande Broan BCR1 est un dispositif sans fil à radiof

Page 3 - PARA CAMPANA

MODELO BCR1Página 3CONTROL REMOTO PARA CAMPANALEA Y CONSERVE ESTAS INSTRUCCIONESEl control remoto BCR1 de Broan es un dispositivo inalámbrico

Page 4 - 99527360A

MODEL/MODÈLE/MODELO BCR1Page/Page/Página 4SERVICE PARTSKEY NO. PART NO. DESCRIPTION1 97018263 Top Cover Assembly (includes stainless cover &

Broan BCR1 Installation Guide

Browse online or download Installation Guide for Unknown Broan BCR1. Broan BCR1 Installation Guide User Manual

Summary of Contents

More documents for Unknown Broan BCR1

Comments to this Manuals

Broan BCR1 Installation Guide

Browse online or download Installation Guide for Unknown Broan BCR1. Broan BCR1 Installation Guide User Manual

Summary of Contents

More documents for Unknown Broan BCR1

Comments to this Manuals

Related products and manuals for Unknown Broan BCR1