Broan RMDDRBK Installation Guide download pdf

MODEL RMDDRBK

REMOTE UP/DOWN CONTROL

For use with RMDD Series Downdraft Ventilators.

INSTALLATION

1. Using the template at right, lay out the 3-hole pattern on the counter top.

Mark the centers of the three holes to be drilled.

2. Carefully drill the three holes through the counter top. Be careful not to

damage or chip the counter top surface when drilling the holes.

3. Remove the control from the plastic bag. Line the control up with the three

holes and position the control so it is parallel with the front of the counter top.

4. Remove the two nylon thumbnuts from the plastic bag and thread onto the

two studs on the control from below the counter top. Hand tighten only.

WARNING: To reduce the risk of burns or ignition of clothing

by reaching across burners, the remote control must be

mounted at least 4" away from any cook top burner.

.250 DIA.

HOLES

.438

DIA.

HOLE

2.000

.750

1.000

.625

5. Remove the blower, clamp channels, and gearmotor cover from downdraft.

Remove the large panel to expose the downdraft's wiring.

When to use the Remote UP/DOWN Control

The Remote UP/DOWN Control should be used when your cooktop has a burner

that is within 4 inches of the UP/DOWN Button on the downdraft chimney.

The Remote UP/DOWN Control

can be used for convenient UP/DOWN opera-

tion of the downdraft chimney (even when a burner is more than 4 inches from

the UP/DOWN Button of the downdraft chimney).

How to use the Remote UP/DOWN Control

Do not place the remote control where it will interfere with cooking, where hot

pans could be set, or where hot liquids could be spilled on the control.

The Remote UP/DOWN Control disables the UP/DOWN function of the UP/

DOWN Button on the downdraft chimney.

6. At the lower right hand corner of downdraft, unplug the cable from the left

side of the wiring box.

7. Remove remote cable from the plastic bag and plug into back of control from below

counter top. Route cable through cabinet to lower right hand corner of downdraft and

through the clearance holes in the side of downdraft and wiring box. Plug cable into

circuit board plug, as shown.

8. Stuff excess cable out of the way, secure the cable so it is not damaged by items

stored in the cabinet, and reassemble downdraft.

CABINET

FLOOR

LOWER

RIGHT

SIDE

DOWNDRAFT

CUT OUT ON DOTTED LINE

WIRING

BOX

REMOTE

CABLE

WIRING

BOX

Note: The downdraft up/down

control must be mounted into

the countertop, at least 4" from

the cooktop.

COUNTERTOP

UP / DOWN

CONTROL

COOKTOP

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO

PERSONS, OBSERVE THE FOLLOWING:

1. Before servicing or cleaning unit, switch power off at service panel and lock

the service disconnecting means to prevent power from being switched on

accidentally. When the service disconnecting means cannot be locked,

securely fasten a prominent warning device, such as a tag, to the service

panel.

2. Installation work and electrical wiring must be done by a qualified person(s)

in accordance with all applicable codes and standards, including fire-rated

construction codes and standards.

3. When cutting or drilling into wall or ceiling, do not damage electrical wiring

and other hidden utilities.

1 2

Summary of Contents

Page 1 - REMOTE UP/DOWN CONTROL

MODEL RMDDRBKREMOTE UP/DOWN CONTROLFor use with RMDD Series Downdraft Ventilators.INSTALLATION1. Using the template at right, lay out the 3-hole patte

Page 2 - WARRANTY

WARRANTYBROAN-NUTONE ONE YEAR LIMITED WARRANTYBroan-NuTone warrants to the original consumer purchaser of its products that such products will be free

Comments to this Manuals

No comments

Broan RMDDRBK Installation Guide

Browse online or download Installation Guide for Unknown Broan RMDDRBK. Broan RMDDRBK Installation Guide User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Unknown Broan RMDDRBK