Broan EW5836SS Installation Manual download pdf (Page 7)

BReAN

MODELS EW5830SS,, EW5836SS

Page 7

OPERATION

Always turn the hood ON before cooking inorder to establish an air

flow in the kitchen. After turning off the range, let the hood run for a

few minutes to clear the air.

Operate the hood as follows: DELAY

OFF FAN OFF LIGHT

LED INDICATORS

OFF

Turns the fan OFF

FAN (1-Pushbutton Switch, 3-Fan Speeds)

Turns the fan ON to the last selected speed, and activates a blue LED

indicatingthe fan speed setting. Pressing the FAN button a second

time will index the fan speed and LED indicatorto the next highest

setting. Pressing the FAN button when the fan is at the highest speed

setting will index the fan and LED indicatorto the lowest setting.

DELAY=OFF(10 Minute Delay=OFF)

Activates the 10 minute delay off feature when the fan is ON (any

speed). When activated, the blue LED indicatorabove the selected

speed setting will blink. The hood fan will automatically turn OFF after

10 minutes has elapsed. The DELAY-OFF button can be pressed at

any time during the 10minute countdown to turn off the feature.

LIGHT (l=Pushbutton Switch, 3=Lightintensities)

Turns the lights ON to the lowest intensity.Pressing the LIGHT button

a second time will index the light intensityto the next highest level.

Pressing the LIGHT button when the lights are at the highest intensity

will turn the lights off.

FILTER CHANGE iNDiCATiON

After 30 hours of fan operation, the three blue LED indicatorswill blink

simultaneously, indicating that it is time to clean the grease filters.

To reset the filter clean timer, press and hold the OFF button for 3

seconds. The blinking LED indicatorswill turn off.

HEAT SENTRY SYSTEM

This range hood is equipped with a standard Heat Sentry system

that monitors excessive temperature and automatically turns the fan

speed on HIGH.

1) If the fan is ON, the Heat Sentry system will increase the fan

setting to its highest speed when the temperature is elevated.

The blue indicatorfor fan speed (3) will illuminate and blink at

a high rate, indicatingthat the heat sentry function is activated.

Once the temperature has reduced, the Heat Sentry system will

change the fan speed to the original setting.

2) If the fan is OFF, the Heat Sentry system will automatically turn

the fan on to its highest speed when the temperature is above

normal. The blue indicator for fan speed (3) will illuminateand

blink at a high rate, indicatingthat the heat sentry function is

activated. After the temperature has lowered to normal, the fan

will turn off.

FUSES

The Range Hood Control Board contains a Main Fuse to protect the

controls from power surges. New fuses can be purchased at a local

electronic supply store. Use 5A, 120V, 5 mm diameter, 20 mm long,

fast-acting, cartridge-type fuses.

To replace a fuse (by qualified person(s):

1. Disconnect power at service entrance.

2. Remove filters

3. Remove control cover

4. Remove and inspectfuse.

MAKE-UP AiR DAMPER

The hood is compatible with Broan Make-Up Air Damper Model

MD6T or Model MD8T (optional). Purchase separately.

MAKE-UP AIR DAMPER

MAKE UP DAMPER CONNECTION

(switched low voltage)

20 GAUGE BELL WIRE FOR LOW

(_ OLTAGE CONNECTION ON

TOP OF HOOD

"'"-- 24V ____

DRY CONTACTTRANSFORMER J

(INCLUDED) / TERMINAL

HOOD BUSHING

FOR LOW

__ 120 VAC / VOLTAGE

-- 60 HZ I CONNECTION

Make the connection to the Make-Up Air Damper with low voltage

wiring, as shown. See Make-Up Air Damper instructions for additional

information.

REMOTE CONTROL

The hood is compatible with Broan Radio Frequency (RF) Remote

Control Model BCR1 (optional). Purchase separately.

To link the BCR1 remote control with the hood, press and hold the

LIGHT button for 3-seconds.

The blue LED indicatorswill turn on and off in succession to indicate

the hood isin RF linking mode. When inthe linking mode, press any

key on the RF remote. An audible beep will be heard at the hood, and

the hood LED's will stop blinking if a successful link is accomplished.

If the remote control did not successfully link with the hood, the linking

mode will be deactivated after 12 seconds, and the LED's will stop

the sequential blinking. Refer to the BCR1 instructionsfor additional

information.

1 2 3 4 5 6 7 8 9 10 11 12 ... 27 28

Comments to this Manuals

No comments

Broan EW5836SS Installation Manual Page 7

Comments to this Manuals

Related products and manuals for Cooker hoods Broan EW5836SS