Broan SSQTXE080 User Manual download pdf (Page 4)

MODELS SSQTXE080 • SSQTXE110

Page 4

2. Remove white paddle/frame from control.

Caution: Do not touch or put anything inside control housing;

control damage may result.

3. Place almond paddle/frame on control.

4. Replace (4) screws and lightly tighten them.

Caution: Do not over tighten screws; frame may crack.

RESTORING POWER TO CONTROL

Control stores all settings in nonvolatile memory; so they are not lost

when power is removed. After power loss, control will automatically

return fan to its state (on or off) before power was interrupted.

HOW TO RESTORE CONTROL FACTORY SETTINGS

This “Restore” procedure clears control’s nonvolatile memory. It

returns control to how it was shipped from factory. All Feature

selections are turned off and all links are removed. “Restore”

procedure should be used cautiously; usually it is used only when

ﬁrst setting up a system or for single unit installations.

Links are unique for each device pair. If one end of the link is

removed, it is important to remove the other end. “Restore” only

removes links within its control. Other link-end needs to be removed

in other device.

CAUTION: Before continuing, choose one of following options: (a)

remove links to target “Restore” control using procedure described

in “How To Remove Speciﬁc Individual Links” or (b) “Restore”

all controls in system and “Restore” all other

LinkLogic™ and

INSTEON™ devices; then links need to be reestablished using

“How To Link SmartSense

System” procedure.

1. Remove power from control’s microcontroller; either: (a)

turn circuit breaker off or (b) pull SET button until it is

fully extended.

2. Wait 15-seconds.

3. Press and hold SET button.

4. For option (1a), turn circuit breaker on while SET button is

pressed. For option (1b), push in and press SET button in

one motion.

5. Continue holding SET button for 3-seconds after power is

applied then release it.

Within 2-seconds, fan and LED turn on; stay on for 1 to

2-seconds and then turn off.

6. If control does not respond as described, start process over

with step 1.

99044387A

Push to

turn ON

Push to

turn OFF

SmartSense

SCREWS

Selection mode. Fan and LED will turn on for one to two seconds

and then turn off.

1. Make sure fan and LED are off; press and release Off paddle.

2. Put control in Feature Selection mode; press and hold On or Off

paddle (approximately 10-seconds) until LED turns on and off

every second (slow-blink).

3. Release paddle.

4. Press and hold On or Off paddle with Feature associated;

Feature status is displayed when LED is steady. Feature is off if

LED is off. Feature is on if LED is on.

5. Release paddle and LED returns to slow-blink.

6. Press and release paddle to toggle Feature on or off.

7. Check Feature status by repeating steps 4 and 5.

8. When done with Feature Selection mode, press and release SET

button.

9. Fan and LED turn on for 1 to 2-seconds and then turn off;

this action conﬁrms new setting is stored and Feature Selection

mode exit.

Feature Selection mode will automatically exit if any paddle is

not pressed within 3-minutes.

HOW TO LINK TO OTHER INSTEON™

(NON-LINKLOGIC™) DEVICES

SmartSense

controls can turn other INSTEON™ enabled devices

on and off and other INSTEON™ devices can turn SmartSense

controls on and off.

1. Put controller device in link mode; refer to device’s installation

instructions.

If SmartSense control is selected as controller then

push and

hold On paddle (approximately 10-seconds) until LED turns on

and off every second (slow-blink). Release On paddle.

2. Go to controlled device and create link according to device’s

installation instructions. For SmartSense control, press and

hold SET button. Continue holding SET button for 3-seconds

then release it. Within 2-seconds, fan and LED turn on; stay on

for 1 to 2-seconds and then turn off.

3. If devices and/or controls do not respond as described, repeat

process beginning with step 1.

HOW TO REMOVE SMARTSENSE

, LINKLOGIC™, AND

INSTEON™ INDIVIDUAL LINKS

Links are two-way communication pathways between devices. It is

important to remove both ends of a link. The following “Remove”

procedure accomplishes this task.

1. On Master control, push and hold Off paddle.

2. Wait (approximately 10-seconds) until LED turns on and off

every second (slow-blink).

3. Release Off paddle.

4. On other control, press and hold SET button.

5. Continue holding SET button for 3-seconds then release it.

Within 2-seconds, fan and LED turn on; stay on for 1 to

2-seconds and then turn off.

6. If control does not respond as described, repeat process

beginning with step 1.

HOW TO CHANGE CONTROL COLOR

An almond paddle/frame assembly is included.

1. Use magnetic #1 Philips screwdriver and remove (4) screws

from white paddle/frame.

PADDLE / FRAME

ASSEMBLY

1 2 3 4 5 6 7 8

Comments to this Manuals

No comments

Broan SSQTXE080 User Manual Page 4

Comments to this Manuals