Broan VX12000C User's Guide download pdf (Page 10)

page 10

HOW TO USE POWER BRUSH/WAND

WAND RELEASE

The power brush is not

recommended for use on

bare floors. Wand release

pedal (A) on power brush

allows you to quickly

disconnect wand and switch

to combination floor/rug tool

for use on bare floors.

POWER BRUSH NECK RELEASE

Push down power brush neck release pedal (B) to unlock

brush neck. Return the neck to the upright position for storage.

POWER BRUSH HEIGHT ADJUSTMENT

The icons (D) refer to the carpet pile

height. Select height by depressing

height adjustment pedal (C) to desired

position: (Extra-Low), (Low),

(Medium) or (High).

HEIGHT ADJUSTMENT LED INDICATORS

The LEDs show the carpet pile covered

by the selected height, e.g.: when

(High) is selected, all LEDs will be lit, since this height

covers all pile heights. So if (Extra-Low) is selected, only the

lowest LED will be lit.

WAND LENGTH ADJUSTMENT

Extend (E) or shorten (F)

the wand to comfortable

work position by holding

the wand grip (G) in one

hand and sliding the upper

section (the one with the

prongs) with the other

hand.

FLOOR HEIGHT

CAUTION

Always pick up hard or sharp objects by hand

before using your power brush. Items such as pins,

hairpins, tacks, crayons, etc., may damage the

brush roll or may break the belt.

CAUTION

Always unlock brush neck before use.

AO0020

AD0022

AD0023

AD0024

EDGE CLEANER

Brush extends full width for effective edge cleaning along both

sides of nozzle. To operate, simply run cleaner along edge

board. Rubber bumper protects furniture and baseboards.

ELECTRONIC CIRCUIT BREAKER

The power brush is equipped

with an electronic circuit breaker

that protects the motor and the

belt if a too large object is

picked up accidentally.

If the power brush stops while

vacuuming, turn the power unit

off using handle. Release the

power brush from the wand

and turn it over to see if there is an obstruction. When brush

roll jam has been cleared, press the reset button (H) and

connect the power brush back to the wand. Finally, turn the

power unit/power brush back on. If it fails to restart or continues

to trip without any apparent reason, the power brush must be

serviced by an authorized service center.

CLEANING AND STORAGE

CLEANING BRUSH ROLL

In order to keep high cleaning efficiency and to prevent

damage to your vacuum cleaner, the brush roll must be

cleaned every time the belt is changed.

The brush roll must also be cleaned according to the following

schedule:

ACUUM CLEANER USE CLEAN BRUSH ROLL

Heavy (used daily) Every week

Moderate (2-3 times per week) Every month

Light (1 time per week) Every 2 months

Check and remove hair, string and lint build-up frequently in

the brush roll and end cap areas. Remove any dirt or debris in

the belt path and in the brush roll areas.

CLEANING HOUSING

To keep the power brush housing clean, it can be wiped with

a damp cloth and a mild soap solution, then thoroughly dried.

Never use any type of chemical as they can damage the housing.

STORAGE

1. Ensure that hose and power cord are disconnected from

wall inlet before unplugging power brush.

2. Disconnect hose handle from wand.

3. Always keep hose neatly coiled when not in use.

4. When not in use, the power brush should be stored in a

clean, dry place.

WARNING

Disconnect electrical supply before servicing or

cleaning the unit. Failure to do so can result in

electrical shock or personal injury from cleaner

suddenly starting.

AD0030

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 16

Comments to this Manuals

No comments

Broan VX12000C User's Guide Page 10

Comments to this Manuals

Related products and manuals for Vacuum cleaners Broan VX12000C